亚洲精品国偷拍自产在线麻豆,国产精品成人观看视频国产奇米,国产成a人亚洲精品无码樱花,无码人妻丰满熟妇精品区

EIGRP路由信息在默認情況下占用接口帶寬的50%，而串行接口默認的帶寬為T1(1.544M)，但在實際上串行接口的帶寬并不是默認值，這里我們按照需求修改接口的帶寬并修改EIGRP 占用帶寬的百分比例。拓撲圖如下：

修改帶寬占用比：

1. R1(config)# interface s0/0
2. R1(config-if)# bandwidth 128 //注意，這里的單位是KB/s
3. R1(config-if)# ip bandwidth-percent eigrp 100 40 //修改EIGRP 路由信息占用帶寬的百分比為40
4. R1(config-if)# end
5.  
6. R2(config)# interface s0/0
7. R2(config-if)# bandwidth 64 //注意，這里的單位是KB/s
8. R2(config-if)# end
9.  
10. R3(config)# interface s0/0
11. R3(config-if)# bandwidth 64 //注意，這里的單位是KB/s
12. R3(config-if)# end

驗證：

1. R1#show interfaces serial 0/0 | include BW
2. MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,

EIGRP 在幀中繼網絡中使用點對點子接口的方式。第4 步配置中，可以看到R2 和R3 想要通過R1 學習到對方宣告的網絡，必須將R1 的接口S0/0 水平分割關閉才可以。這里我們使用幀中繼網絡點對點子接口的方法來完成。
點對點子接口方式：

1. R1(config)#default interface Serial 0/0　//將接口的配置還原為默認值
2. Building configuration…
3.  
4. Interface Serial0/0 set to default configuration
5. R1(config)#
6. *Mar 1 01:45:30.363: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.3 (Serial0/0) is resync: split horizon changed
7. *Mar 1 01:45:30.367: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.2 (Serial0/0) is resync: split horizon changed
8. *Mar 1 01:45:30.779: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.3 (Serial0/0) is down: interface down
9. *Mar 1 01:45:30.787: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.2 (Serial0/0) is down: interface down
10. *Mar 1 01:45:31.483: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
11. *Mar 1 01:45:33.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
12. R1(config)#interface Serial 0/0
13. R1(config-if)#encapsulation fram 　//封裝為幀中繼模式
14. R1(config-if)#no fram inv //關閉自動獲取
15. R1(config-if)#no sh
16. R1(config-if)#ip split eigrp 100 //打開水平分割
17. R1(config-if)#int s0/0.1 point //設置點對點子接口
18. R1(config-subif)#ip add 192.168.1.1 255.255.255.252
19. R1(config-subif)#fram interface-dlci 102 //指定接口DLCI 號
20. R1(config-fr-dlci)#int s0/0.2 point //配置R1 和R3 之間的子接口
21. R1(config-subif)#ip add 192.168.1.5 255.255.255.252
22. R1(config-subif)#fram interface-dlci 103
23. *Mar 1 01:47:05.767: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.2 (Serial0/0.1) is up: new adjacency
24. *Mar 1 01:47:06.651: IP-EIGRP(Default-IP-Routing-Table:100): Neighbor 192.168.1.3 not on common subnet for Serial0/0.2
25. R1(config-fr-dlci)#end

因為R1 和R2 相連的子接口IP 地址和子網掩碼有所變化必須修改

1. R2(config)#int s0/0
2. R2(config-if)#ip add 192.168.1.2 255.255.255.252

因為R1 和R3 相連的子接口IP 地址和子網掩碼有所變化必須修改

1. R3(config)#int s0/0
2. R3(config-if)#ip add 192.168.1.6 255.255.255.252
3. *Mar 1 01:47:51.331: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.5 (Serial0/0) is down: address changed
4. *Mar 1 01:47:51.343: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.1 (Serial0/0) is down: address changed
5. *Mar 1 01:47:52.463: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor 192.168.1.5 (Serial0/0) is up: new adjacency
6. R3(config-if)#no frame-relay map ip 192.168.1.1 301 broadcas //將之前配置的取消
7. R3(config-if)#fram map ip 192.168.1.5 301 br

驗證配置：

1. R1#show ip eigrp neighbors
2. IP-EIGRP neighbors for process 100
3. H Address Interface Hold Uptime SRTT RTO Q Seq
4. (sec) (ms) Cnt Num
5. 1 192.168.1.6 Se0/0.2 173 00:06:53 117 1053 0 15
6. 0 192.168.1.2 Se0/0.1 135 00:07:12 1055 5000 0 16
7.  
8. R3#ping 10.1.1.1
9.  
10. Type escape sequence to abort.
11. Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds:
12. !!!!!
13. Success rate is 100 percent (5/5), round-trip min/avg/max = 20/89/180 ms

EIGRP和幀中繼的配置實例說明請閱讀：幀中繼交換機和路由器模擬配置和EIGRP路由協議的配置實例解析